#BLUE SCREEN KERNEL_DATA_INPAGE_ERROR DRIVER#
#BLUE SCREEN KERNEL_DATA_INPAGE_ERROR MANUAL#
#BLUE SCREEN KERNEL_DATA_INPAGE_ERROR CODE#
#BLUE SCREEN KERNEL_DATA_INPAGE_ERROR WINDOWS#

For more information about these procedures, see the owner's manual for your computer.Д¬heck that all the adapter cards in the computer are properly seated. Resolving a failing RAM problem: Run the hardware diagnostics that the system manufacturer supplies, especially the memory scanner. Resolving a defective hardware problem: If the I/O status is C0000185 and the paging file is on an SCSI disk, check the disk cabling and SCSI termination for problems. Always use the version of Chkdsk that matches your version of Windows.

#BLUE SCREEN KERNEL_DATA_INPAGE_ERROR WINDOWS#

Warning If your system partition is formatted with the FAT file system, the long file names that the Windows operating system uses might be damaged if you use Scandisk or another MS-DOS-based hard disk tool to verify the integrity of your hard disk from MS-DOS. If you cannot start the computer because of the error, use the Recovery Console and run Chkdsk /r. You must restart the computer before the disk scan begins. Run Chkdsk /f /r on the system partition. If Autochk does not scan the hard disk for errors, you can manually start the disk scanner. If you can restart the computer after the error, Autochk runs automatically and attempts to map the bad sector to prevent it from being used anymore.

#BLUE SCREEN KERNEL_DATA_INPAGE_ERROR CODE#

Resolving a bad block problem: An I/O status code of 0xC000009C or 0xC000016A typically indicates that the data could not be read from the disk because of a bad block (sector).

#BLUE SCREEN KERNEL_DATA_INPAGE_ERROR DRIVER#

For more information about other possible status codes that can be returned, see the Ntstatus.h file in the Microsoft Windows Driver Kit (WDK).ДЄnother common cause of this error message is defective hardware or failing RAM.ДЄ virus infection can also cause this bug check. These status codes are the most common ones that have specific causes. If you are using older PATA (IDE) drives, this status code can indicate an incorrect master/subordinate drive configuration. Check your cables and check the drive with the diagnostic utility available from your drive manufacturer. Some common status codes include the following:Д xC000009A, or STATUS_INSUFFICIENT_RESOURCES, indicates a lack of nonpaged pool resources.Д xC000009C, or STATUS_DEVICE_DATA_ERROR, typically indicates bad blocks (sectors) on the hard disk.Д xC000009D, or STATUS_DEVICE_NOT_CONNECTED, indicates defective or loose cabling, termination, or that the controller does not see the hard disk.Д xC000016A, or STATUS_DISK_OPERATION_FAILED, indicates bad blocks (sectors) on the hard disk.Д xC0000185, or STATUS_IO_DEVICE_ERROR, indicates improper termination or defective cabling on SCSI devices or that two devices are trying to use the same IRQ.Д xC000000E, or STATUS_NO_SUCH_DEVICE, indicates a hardware failure or an incorrect drive configuration. The address of the page table entry (PTE)ДЇrequently, you can determine the cause of the KERNEL_DATA_INPAGE_ERROR bug check from the error status (Parameter 2). Otherwise, the parameters have the following definitions. The address of the InPageSupport structure The error status (typically an I/O status code) If the first parameter is 3 (and the third parameter is nonzero) or 4, the parameters have the following definitions. The virtual address that could not be paged into memory

The error status (usually an I/O status code) If the first parameter is 1 or 2, or 3 and the third parameter is 0, the parameters have the following definitions. The four parameters that are listed in the message can have three possible meanings. If you are a customer who has received a blue screen error code while using your computer, see Troubleshoot blue screen errors.

Blue screen kernel_data_inpage_error